Call 000 000 0000

Seismic Straps, T&P Drains and Garage Rules in Riverside, CA

Straps and a T&P drain are code, not optional accessories.

Call 000 000 0000Placeholder number while the live line is set up.
  • Tankless and tank
  • Gas and electric
  • Riverside and nearby cities
Photo for the Riverside article “Straps and T&P Rules”: California strapping law and Riverside T&P and garage installation rules.Illustration

Last updated

California law requires residential water heaters to be braced, anchored or strapped against earthquake motion, and the City of Riverside's handout shows how that usually looks on a tank. The same handout covers T&P drains, garage burner height and combustion air. These rules apply to new, replacement and existing residential heaters. They are not decoration.

Health and Safety Code section 19211

Section 19211 says all new and replacement water heaters, and all existing residential water heaters, shall be braced, anchored or strapped to resist falling or horizontal displacement due to earthquake motion, at a minimum in accordance with the California Plumbing Code. Sellers must certify compliance in writing. The section defines a water heater, for this purpose, as a standard unit of not more than 120 gallons for which a preengineered strapping kit is readily available.

What the city handout adds

The Riverside Water Heater Installations handout says straps belong in the upper third and the lower third of the tank, with at least four inches between the controls and the lower strap. It describes backer blocks when there is no stud directly behind the heater. It also requires a T&P drain to the outside, not smaller than the valve outlet, of listed materials, terminating not more than 24 inches and not less than 6 inches from the ground, unless the inspector accepts another listed method.

Rather explain it out loud? One call covers it.

Call 000 000 0000

Garages

Gas water heaters in garages, and in spaces that open to a garage, must have burners and ignition devices at least 18 inches above the floor unless the unit is listed as flammable-vapor ignition resistant. The heater must be located or protected so a moving vehicle cannot damage it. Combustion-air openings, when required, start within 12 inches of the top and bottom of the enclosure and must be at least 100 square inches each, per the handout's CPC excerpts.

Electric tanks and tankless units

Electric tanks still need straps. A tankless unit is mounted to the structure rather than strapped like a tall tank, but it still has to be installed as listed, with correct venting and support. The strapping law is easiest to picture on a tank; the listing and the inspector still matter on a wall-hung unit.

When you call

If a tank is walking, a strap is missing, or a T&P pipe dumps into a garage floor drain, mention it. A replacement or a repair is the usual path. Missing straps on a sale or a refinance are a legal and safety issue, not a cosmetic one.

What a proper strap job looks like in practice

On a typical tank, you should see two substantial straps, not a single loose cable and not a length of wire. One strap sits in the upper third of the tank, the other in the lower third, with the lower strap kept clear of the controls. The straps should be anchored into structure, not into drywall alone. If the tank sits away from the studs, the city's handout describes backer blocks so the tank cannot lean. A kit that is still in its bag in the corner of the garage does not count.

Tankless units are not strapped the same way. They are lagged or otherwise fastened to the wall as the manufacturer requires, and that fastening still has to resist earthquake motion. A unit hanging from two weak fasteners in particle board is not a listed install.

T&P valves, drains and what "to the outside" means

The temperature and pressure relief valve is a safety device. It must be the right valve for the heater, and its drain must be able to discharge without scalding someone in the garage or dumping into a closed space. The city's handout describes a drain that is at least the size of the valve outlet, made of listed materials, and terminated close to the ground outside unless another listed method is approved. A drain that ends in a shop-vac bucket, or a valve that has been plugged, is a safety problem, not a handy shortcut.

Never sit on the T&P lever "to test it" if you do not know whether the drain is clear and routed correctly. A stuck valve can dribble or fail to reseat. If a T&P valve is leaking, call about a repair rather than capping it.

Sales, refinances and rental units

Section 19211's written certification at sale is why real-estate inspections often flag missing straps. A refinance or an insurance question can raise the same issue. On a rental, the owner is usually the one who has to bring the heater into compliance. This site does not give legal advice and does not fill out disclosure forms. It can connect you with a provider who can look at the straps and the T&P path.

Expanded tanks, stands and pans

An expansion tank, a stand and a drain pan do not replace straps. They are separate parts of a complete install. A tank on a stand still has to be strapped to the structure. A pan is for leaks, not for earthquakes. If a previous installer skipped one item to finish quickly, the next visit should correct the list, not add a second shortcut.

What to do next

Look at the tank from a safe distance. If straps are missing, loose, rusted through or clearly too low across the gas control, you have a reason to call. If the T&P pipe is missing, crushed or ending in the middle of a parking space, mention that too. For a full replacement, straps and the T&P drain should be part of the job, not an upgrade. See the City of Riverside permits page if you want the official permit context as well.

Talk it through by phone

Call the number on this page if you want to talk through how this applies to your heater and address. Have the city, the fuel and the location of the unit ready. Coverage is confirmed on the call.

Sources checked

Reviewed November 17, 2026. Confirm anything important with the agency, since rules and programs change.

Riverside-area hot water, sorted by phone

Calling from Riverside, CA? Describe the heater, ask whether your address is covered, and hear the next step. Call to check availability.

Call 000 000 0000
No hot water in Riverside?Call 000 000 0000